This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
rini:to-do_2011 [2011/04/28 04:11] ben [To-Do] |
rini:to-do_2011 [2011/04/28 04:18] (current) ben [To-Do] |
||
---|---|---|---|
Line 12: | Line 12: | ||
=== Engine/Systems === | === Engine/Systems === | ||
+ | |||
* Install security bolts | * Install security bolts | ||
* motor mount, sliding up, could be lowered a bit? | * motor mount, sliding up, could be lowered a bit? | ||
=== Mast === | === Mast === | ||
- | * <del>New Windex</del>need to bend indicators back into place | + | |
- | * <del>Replace masthead lamp with LED</del> | + | * Need to bend windex indicators back into place |
- | * <del>Install baton to lift backstay over sail headboard when tacking?</del>Need a bigger/stronger baton | + | * Need a bigger/stronger baton installed on the back stay |
- | * <del>Forestay- rubs against jib halyard sheave, move it outside of the sheave position or remember to keep backstay loose (Found a suitable piece of steel to use to move the stay forward a centimeter or two)</del>Sheave was in great shape, this isn't necessary | + | |
- | * <del>Replace lower boom kicker bracket (maybe upper too?) with something more sturdy</del>Bent back into shape, re-riveted | + | |
=== Sails/Rigging === | === Sails/Rigging === | ||
- | * <del>Shorten lower boom kicker length and re-attach (will allow more downward movement), need hacksaw and riveter at the boat</del> | + | * **New sail cover** to allow leaving sail slides in the slot |
- | * <del>Re-install washers on jib halyard block</del> | + | |
- | * **New sail cover** | + | |
=== Hull === | === Hull === | ||
- | * <del>Sand and</del> varnish tiller, needs two more coats | + | * <del>Sand and</del> varnish tiller, could use two more coats |
- | * Replace toe-rails or patch broken toe-rail section | + | * Replace toe-rails or patch broken toe-rail section (have 1m teak piece) |
* Replace or refinish hatch-cover | * Replace or refinish hatch-cover | ||
* Install external hatch handle | * Install external hatch handle | ||
Line 39: | Line 36: | ||
=== Cabin === | === Cabin === | ||
- | * Remove old log and fill holes | + | * Remove old speed log and fill holes |
- | * <del>Glue metal plate back into place under stove hatch - don't think it will last, need screws instead (DIDN'T hold).</del>Bolted down. | + | |
* File pantry and stove cover doors down to allow for expansion | * File pantry and stove cover doors down to allow for expansion | ||
* Re-attach trim to various panels | * Re-attach trim to various panels | ||
- | * Floor board reinforce forward port side | + | * Floor board reinforce forward port side |
+ | * Floor board sand down bilge cover | ||
* Paint inside walls near cabin entrance | * Paint inside walls near cabin entrance | ||
* Sand and varnish walls underneath added deck supports (varnish is peeling) | * Sand and varnish walls underneath added deck supports (varnish is peeling) | ||
Line 50: | Line 47: | ||
* Safety lines - or at least a bow pulpit | * Safety lines - or at least a bow pulpit | ||
- | * Lazy jacks? | ||
* Window replacement | * Window replacement | ||
* Find replacement mast support pole? Need to prime the top section of the pole, a bit of rust. | * Find replacement mast support pole? Need to prime the top section of the pole, a bit of rust. | ||
Line 56: | Line 52: | ||
==== Completed ==== | ==== Completed ==== | ||
- | * Weld tiller bracket back together | + | |
=== Hull === | === Hull === | ||
+ | * <del>Weld tiller bracket back together</del> | ||
* <del>Patch small paint crack just above water line on starboard side near stern</del> | * <del>Patch small paint crack just above water line on starboard side near stern</del> | ||
* <del>Check rudder bearings and shaft condition</del> Should be okay for a long time to come. | * <del>Check rudder bearings and shaft condition</del> Should be okay for a long time to come. | ||
Line 68: | Line 65: | ||
* <del>Remove lost/dropped halyard blocks from center of mast</del> DONE! | * <del>Remove lost/dropped halyard blocks from center of mast</del> DONE! | ||
* <del>Either get 12-20 screws for spreaders or drill out to MM size</del> Drilled and tapped to M6! | * <del>Either get 12-20 screws for spreaders or drill out to MM size</del> Drilled and tapped to M6! | ||
+ | * <del>New Windex</del> | ||
+ | * <del>Replace masthead lamp with LED</del> | ||
+ | * <del>Install baton to lift backstay over sail headboard when tacking?</del> | ||
+ | * <del>Forestay- rubs against jib halyard sheave, move it outside of the sheave position or remember to keep backstay loose (Found a suitable piece of steel to use to move the stay forward a centimeter or two)</del>Sheave was in great shape, this isn't necessary | ||
+ | * <del>Replace lower boom kicker bracket (maybe upper too?) with something more sturdy</del>Bent back into shape, re-riveted | ||
+ | |||
+ | === Sails/Rigging === | ||
+ | |||
+ | * <del>Shorten lower boom kicker length and re-attach (will allow more downward movement), need hacksaw and riveter at the boat</del> | ||
+ | * <del>Re-install washers on jib halyard block</del> | ||
+ | |||
+ | === Cabin === | ||
+ | |||
+ | * <del>Glue metal plate back into place under stove hatch - don't think it will last, need screws instead (DIDN'T hold).</del>Bolted down. | ||
==== Bottom painting supplies ==== | ==== Bottom painting supplies ==== |