rini:to-do_2011
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
rini:to-do_2011 [2011/04/11 04:49] ben [Completed] |
rini:to-do_2011 [2011/04/28 04:18] ben [Completed] |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| === Engine/Systems === | === Engine/Systems === | ||
| + | |||
| * Install security bolts | * Install security bolts | ||
| - | * Replace motor mount plywood | ||
| - | * Depth sounder is dead- repair | ||
| * motor mount, sliding up, could be lowered a bit? | * motor mount, sliding up, could be lowered a bit? | ||
| - | * replace starter battery with storage battery | ||
| === Mast === | === Mast === | ||
| - | * New Windex | + | |
| - | * Replace masthead lamp with LED | + | * Need to bend windex indicators back into place |
| - | * Install baton to lift backstay over sail headboard when tacking? | + | * Need a bigger/stronger baton installed on the back stay |
| - | * Forestay- rubs against jib halyard sheave, move it outside of the sheave position or remember to keep backstay loose (Found a suitable piece of steel to use to move the stay forward a centimeter or two) | + | |
| - | * Replace lower boom kicker bracket (maybe upper too?) with something more sturdy | + | |
| === Sails/Rigging === | === Sails/Rigging === | ||
| - | * Shorten lower boom kicker length and re-attach (will allow more downward movement), need hacksaw and riveter at the boat | + | * **New sail cover** to allow leaving sail slides in the slot |
| - | * <del>Re-install washers on jib halyard block</del> | + | |
| - | * **New sail cover** | + | |
| === Hull === | === Hull === | ||
| - | * <del>Sand and</del> varnish tiller, needs two more coats | + | * <del>Sand and</del> varnish tiller, could use two more coats |
| - | * Replace toe-rails | + | * Replace toe-rails or patch broken toe-rail section (have 1m teak piece) |
| - | * Replace hatch-cover | + | * Replace or refinish hatch-cover |
| * Install external hatch handle | * Install external hatch handle | ||
| * Replace wood underneath spinnaker barber-haul cleats | * Replace wood underneath spinnaker barber-haul cleats | ||
| - | * Reattach (replace?) cockpit floorboards | + | * Patch random small cracks on deck & in cockpit |
| - | * Patch random cracks on deck & in cockpit | + | |
| === Cabin === | === Cabin === | ||
| - | * Remove old log and fill holes | + | * Remove old speed log and fill holes |
| - | * Glue metal plate back into place under stove hatch - don't think it will last, need screws instead (DIDN'T hold). | + | |
| * File pantry and stove cover doors down to allow for expansion | * File pantry and stove cover doors down to allow for expansion | ||
| * Re-attach trim to various panels | * Re-attach trim to various panels | ||
| - | * Floor board reinforce forward port side - completely rebuilding the forward floor boards, will take several gluing sessions and new screws. | + | * Floor board reinforce forward port side |
| + | * Floor board sand down bilge cover | ||
| * Paint inside walls near cabin entrance | * Paint inside walls near cabin entrance | ||
| * Sand and varnish walls underneath added deck supports (varnish is peeling) | * Sand and varnish walls underneath added deck supports (varnish is peeling) | ||
| - | * Install hook under cabin hatch to allow easier spinnaker stowage (have brass hooks, but maybe something with a latch would be better) | ||
| === Long-term === | === Long-term === | ||
| + | |||
| * Safety lines - or at least a bow pulpit | * Safety lines - or at least a bow pulpit | ||
| * Lazy jacks? | * Lazy jacks? | ||
| * Window replacement | * Window replacement | ||
| - | * Find replacement mast support pole? Need to deal with the top section of the pole, quite a bit of rust. | + | * Find replacement mast support pole? Need to prime the top section of the pole, a bit of rust. |
| + | * Replace motor mount plywood | ||
| ==== Completed ==== | ==== Completed ==== | ||
| - | * Weld tiller bracket back together | + | |
| === Hull === | === Hull === | ||
| + | * <del>Weld tiller bracket back together</del> | ||
| * <del>Patch small paint crack just above water line on starboard side near stern</del> | * <del>Patch small paint crack just above water line on starboard side near stern</del> | ||
| * <del>Check rudder bearings and shaft condition</del> Should be okay for a long time to come. | * <del>Check rudder bearings and shaft condition</del> Should be okay for a long time to come. | ||
| Line 71: | Line 66: | ||
| * <del>Remove lost/dropped halyard blocks from center of mast</del> DONE! | * <del>Remove lost/dropped halyard blocks from center of mast</del> DONE! | ||
| * <del>Either get 12-20 screws for spreaders or drill out to MM size</del> Drilled and tapped to M6! | * <del>Either get 12-20 screws for spreaders or drill out to MM size</del> Drilled and tapped to M6! | ||
| + | * <del>New Windex</del> | ||
| + | * <del>Replace masthead lamp with LED</del> | ||
| + | * <del>Install baton to lift backstay over sail headboard when tacking?</del> | ||
| + | * <del>Forestay- rubs against jib halyard sheave, move it outside of the sheave position or remember to keep backstay loose (Found a suitable piece of steel to use to move the stay forward a centimeter or two)</del>Sheave was in great shape, this isn't necessary | ||
| + | * <del>Replace lower boom kicker bracket (maybe upper too?) with something more sturdy</del>Bent back into shape, re-riveted | ||
| + | |||
| + | === Sails/Rigging === | ||
| + | |||
| + | * <del>Shorten lower boom kicker length and re-attach (will allow more downward movement), need hacksaw and riveter at the boat</del> | ||
| + | * <del>Re-install washers on jib halyard block</del> | ||
| + | |||
| + | === Cabin === | ||
| + | |||
| + | * <del>Glue metal plate back into place under stove hatch - don't think it will last, need screws instead (DIDN'T hold).</del>Bolted down. | ||
| ==== Bottom painting supplies ==== | ==== Bottom painting supplies ==== | ||
rini/to-do_2011.txt · Last modified: 2011/04/28 04:18 by ben
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
