mspacman:pi
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
mspacman:pi [2013/10/03 05:21] ben |
mspacman:pi [2013/10/06 08:40] (current) ben |
||
|---|---|---|---|
| Line 818: | Line 818: | ||
| Went looking to see if there might be a compiler issue with the undefined references, running "gcc version 4.6.3 (Debian 4.6.3-14+rpi1)", there's a 4.7 version available, installing it via ''sudo apt-get install gcc-4.7''. | Went looking to see if there might be a compiler issue with the undefined references, running "gcc version 4.6.3 (Debian 4.6.3-14+rpi1)", there's a 4.7 version available, installing it via ''sudo apt-get install gcc-4.7''. | ||
| + | |||
| + | Re-instated the devcb_read lines in ay8910.c, make clean, make. | ||
| + | |||
| + | No difference, and everything I try to do gets a "Bus error". Boo. | ||
| + | |||
| + | Gave up, looked around, realized I also had a version of xmame someone distributed that's new enough to support mspacmnf. Compiled it over the course of two days, all set. | ||
| + | |||
| + | Added user: mspacman | ||
| + | |||
| + | Edited /etc/X11/xinit/xinitrc to be: | ||
| + | <code> | ||
| + | #. /etc/X11/Xsession | ||
| + | /mame/xmame.SDL | ||
| + | </code> | ||
| + | |||
| + | Edited /etc/inittab: | ||
| + | <code> | ||
| + | #1:2345:respawn:/sbin/getty --noclear 38400 tty1 | ||
| + | 1:2345:respawn:/bin/login -f mspacman tty1 </dev/tty1 >/dev/tty1 2>&1 | ||
| + | 2:2345:respawn:/bin/login -f mspacman tty2 </dev/tty2 >/dev/tty2 2>&1 | ||
| + | 3:2345:respawn:/bin/login -f mspacman tty3 </dev/tty3 >/dev/tty3 2>&1 | ||
| + | </code> | ||
| + | |||
| + | Edited /etc/rc.local: | ||
| + | <code> | ||
| + | su -l mspacman -c startx | ||
| + | initctl start tty TTY=/dev/tty2 & | ||
| + | initctl start tty TTY=/dev/tty3 & | ||
| + | </code> | ||
| + | |||
| + | Spent last night trying to get sound working- for some reason it works running via VNC, but not running as mspacman. This morning realized maybe it was permissions, ran the prog as user pi and sound exists. Checked group memberships, matched them (things like "audio" and "video" were missing!), and finally- sound. | ||
| + | |||
| + | Upped the clock to 800Mhz, set xinitrc to use volume -3. Rebooted, boat work time. | ||
| + | |||
| + | |||
| + | **TO-DO: get a proper shutdown routine working from GPIO pins or investigate ACPI, check on hiscore.dat instead of saved states- hi score doesn't seem to be working.** | ||
| + | |||
mspacman/pi.1380792115.txt.gz ยท Last modified: 2013/10/03 05:21 by ben
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
