This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
mspacman:mspacman [2010/09/24 03:41] ben |
mspacman:mspacman [2013/09/26 08:43] ben |
||
---|---|---|---|
Line 52: | Line 52: | ||
====== To-Do ====== | ====== To-Do ====== | ||
* <del>Modify Plymouth boot splash theme to be ms. pacman figure...</del> Document & rename plymouth theme. | * <del>Modify Plymouth boot splash theme to be ms. pacman figure...</del> Document & rename plymouth theme. | ||
+ | * <del>Add sound</del> | ||
+ | * <del>Add linear power supply/wall-wart outlet to power sound</del> | ||
* Disable any Mouse in X since the pointer comes back after changing to/from a TTY. (see xorg.conf "void" driver options) | * Disable any Mouse in X since the pointer comes back after changing to/from a TTY. (see xorg.conf "void" driver options) | ||
* <del>Rotate vesa/standard video too?</del> (done- but how did i do it? ah, see above fbcon= boot parameter) | * <del>Rotate vesa/standard video too?</del> (done- but how did i do it? ah, see above fbcon= boot parameter) | ||
Line 61: | Line 63: | ||
* make/buy very short vga cable | * make/buy very short vga cable | ||
* <del>through-holes w/bolts in joystick frame for frame itself</del> | * <del>through-holes w/bolts in joystick frame for frame itself</del> | ||
- | * sheet metal for player 1 & 2 buttons | + | * <del>sheet metal for player 1 & 2 buttons</del> |
* <del>sheet metal base for motherboard/power supply</del> could use reinforcement | * <del>sheet metal base for motherboard/power supply</del> could use reinforcement | ||
- | * convert power from two cords to single, frame-mounted input | + | * <del>convert power from two cords to single, frame-mounted input</del> |
+ | * add mains power switch and extension cord plug input to leg (so computer power cord isn't necessary) | ||
* move distro from hard disk to usb disk and generate second copy on second thumb drive? (as-is distro is ~2.6 gig, surely can be cleaned up) | * move distro from hard disk to usb disk and generate second copy on second thumb drive? (as-is distro is ~2.6 gig, surely can be cleaned up) | ||
+ | * add top glass w/mounts to hold in place | ||
+ | |||
+ | |||
+ | ---- | ||
+ | ====== Gallery ====== | ||
+ | |||
+ | Yep- it's still pretty rough at this point. It plays and sound is working (note the wall-wort plugged into an aux power outlet mounted to the side of the PC supply, necessary for the audio amp IC to work without gobs of switching noise). | ||
+ | |||
+ | Top glass is likely next. | ||
+ | |||
+ | {{gallery>:mspacman:gallery?lightbox}} | ||
+ | |||
+ | ====== Pi ====== | ||
+ | <code> | ||
+ | pi@pi ~ $ cat /boot/config.txt | ||
+ | # uncomment if you get no picture on HDMI for a default "safe" mode | ||
+ | #hdmi_safe=1 | ||
+ | |||
+ | # uncomment this if your display has a black border of unused pixels visible | ||
+ | # and your display can output without overscan | ||
+ | #disable_overscan=1 | ||
+ | |||
+ | # uncomment the following to adjust overscan. Use positive numbers if console | ||
+ | # goes off screen, and negative if there is too much border | ||
+ | #overscan_left=16 | ||
+ | #overscan_right=16 | ||
+ | #overscan_top=16 | ||
+ | #overscan_bottom=16 | ||
+ | |||
+ | # uncomment to force a console size. By default it will be display's size minus | ||
+ | # overscan. | ||
+ | #framebuffer_width=1280 | ||
+ | #framebuffer_height=1024 | ||
+ | #framebuffer_height=720 | ||
+ | |||
+ | # uncomment if hdmi display is not detected and composite is being output | ||
+ | #hdmi_force_hotplug=1 | ||
+ | |||
+ | # uncomment to force a specific HDMI mode (this will force VGA) | ||
+ | hdmi_group=2 | ||
+ | hdmi_mode=35 | ||
+ | |||
+ | |||
+ | # uncomment to force a HDMI mode rather than DVI. This can make audio work in | ||
+ | # DMT (computer monitor) modes | ||
+ | #hdmi_drive=2 | ||
+ | |||
+ | # uncomment to increase signal to HDMI, if you have interference, blanking, or | ||
+ | # no display | ||
+ | config_hdmi_boost=4 | ||
+ | |||
+ | # uncomment for composite PAL | ||
+ | #sdtv_mode=2 | ||
+ | |||
+ | #uncomment to overclock the arm. 700 MHz is the default. | ||
+ | #arm_freq=800 | ||
+ | |||
+ | # for more options see http://elinux.org/RPi_config.txt | ||
+ | gpu_mem=16 | ||
+ | </code> |