This shows you the differences between two versions of the page.
Both sides previous revision Previous revision | Last revision Both sides next revision | ||
iw31:to-do [2016/06/17 12:19] ben [Spring 2016 (sale)] |
iw31:to-do [2016/06/17 13:26] ben |
||
---|---|---|---|
Line 3: | Line 3: | ||
* <del>Finish re-wire</del> | * <del>Finish re-wire</del> | ||
- | * finish runs, bundle all together | + | * <del>finish runs, bundle all together</del> |
- | * panel, auto-pilot, water pump, mast lamps, bundle for nav light switches | + | * <del>panel, auto-pilot, water pump, mast lamps, bundle for nav light switches</del> |
- | * screw down NMEA T's | + | * <del>screw down NMEA T's</del> |
- | * remove old fuse box | + | * <del>remove old fuse box</del> |
* move house battery forward | * move house battery forward | ||
* cable runs to second house battery | * cable runs to second house battery | ||
- | * remove old cabling | + | * <del>remove old cabling</del> |
* New bracket for mast-head lamp | * New bracket for mast-head lamp | ||
* Cleanup & paint, new contact cement for some of the wallpaper | * Cleanup & paint, new contact cement for some of the wallpaper | ||
* Varnish bulkhead (fill screw holes with wood putty) | * Varnish bulkhead (fill screw holes with wood putty) | ||
- | * | ||
===== Spring 2015 ===== | ===== Spring 2015 ===== | ||
Line 20: | Line 19: | ||
* <del>repair sail cover</del> | * <del>repair sail cover</del> | ||
* <del>new curtains, fix-up curtain rods</del> | * <del>new curtains, fix-up curtain rods</del> | ||
- | * mast cabling connector install | ||
* add switch for paralleling relay control? | * add switch for paralleling relay control? | ||
- | * new battery charger? | ||
- | * Re-wire 220v interface | ||
* Find good insulation and storage bins to re-do ice box | * Find good insulation and storage bins to re-do ice box | ||
* make styrofoam cutter with soldering iron & wire & coping saw? | * make styrofoam cutter with soldering iron & wire & coping saw? | ||
- | * Find flexible conduit for wiring runs | + | * <del>new diaphragm bilge pump install (done save clamps, two wood screws, and something to hold output hose from shaking)</del> |
- | * new diaphragm bilge pump install (done save clamps, two wood screws, and something to hold output hose from shaking) | + | |
- | * replace last big of bilge pump line, it's brittle | + | |
* <del>Move cooker gimbals forward in the box, outwards on the sides (thinner boards for mounts), and mount the cooker and pot holder</del> Done! | * <del>Move cooker gimbals forward in the box, outwards on the sides (thinner boards for mounts), and mount the cooker and pot holder</del> Done! | ||
* <del>Drill Ikea mixing bowls for pre-heating cups on cooker, cut them down by 1.5cm vertically to fit</del> | * <del>Drill Ikea mixing bowls for pre-heating cups on cooker, cut them down by 1.5cm vertically to fit</del> | ||
- | * Fix-up the head: [[http://www.groco.net/svc-main.htm|http://www.groco.net/svc-main.htm]] | ||
* Add mixing bowl below water separator/fuel filter | * Add mixing bowl below water separator/fuel filter | ||
| |