iw31:to-do
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
iw31:to-do [2016/04/28 05:53] ben [Spring 2016 (sale)] |
iw31:to-do [2016/06/17 13:26] ben |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ===== Spring 2016 (sale) ===== | ===== Spring 2016 (sale) ===== | ||
| - | * Finish re-wire | + | * <del>Finish re-wire</del> |
| - | * finish runs, bundle all together | + | * <del>finish runs, bundle all together</del> |
| - | * panel, auto-pilot, water pump, mast lamps, bundle for nav light switches | + | * <del>panel, auto-pilot, water pump, mast lamps, bundle for nav light switches</del> |
| - | * screw down NMEA T's | + | * <del>screw down NMEA T's</del> |
| - | * remove old fuse box | + | * <del>remove old fuse box</del> |
| * move house battery forward | * move house battery forward | ||
| * cable runs to second house battery | * cable runs to second house battery | ||
| - | * remove old cabling | + | * <del>remove old cabling</del> |
| * New bracket for mast-head lamp | * New bracket for mast-head lamp | ||
| * Cleanup & paint, new contact cement for some of the wallpaper | * Cleanup & paint, new contact cement for some of the wallpaper | ||
| * Varnish bulkhead (fill screw holes with wood putty) | * Varnish bulkhead (fill screw holes with wood putty) | ||
| - | * | ||
| ===== Spring 2015 ===== | ===== Spring 2015 ===== | ||
| Line 20: | Line 19: | ||
| * <del>repair sail cover</del> | * <del>repair sail cover</del> | ||
| * <del>new curtains, fix-up curtain rods</del> | * <del>new curtains, fix-up curtain rods</del> | ||
| - | * mast cabling connector install | ||
| * add switch for paralleling relay control? | * add switch for paralleling relay control? | ||
| - | * new battery charger? | ||
| - | * Re-wire 220v interface | ||
| * Find good insulation and storage bins to re-do ice box | * Find good insulation and storage bins to re-do ice box | ||
| * make styrofoam cutter with soldering iron & wire & coping saw? | * make styrofoam cutter with soldering iron & wire & coping saw? | ||
| - | * Find flexible conduit for wiring runs | + | * <del>new diaphragm bilge pump install (done save clamps, two wood screws, and something to hold output hose from shaking)</del> |
| - | * new diaphragm bilge pump install (done save clamps, two wood screws, and something to hold output hose from shaking) | + | |
| - | * replace last big of bilge pump line, it's brittle | + | |
| * <del>Move cooker gimbals forward in the box, outwards on the sides (thinner boards for mounts), and mount the cooker and pot holder</del> Done! | * <del>Move cooker gimbals forward in the box, outwards on the sides (thinner boards for mounts), and mount the cooker and pot holder</del> Done! | ||
| * <del>Drill Ikea mixing bowls for pre-heating cups on cooker, cut them down by 1.5cm vertically to fit</del> | * <del>Drill Ikea mixing bowls for pre-heating cups on cooker, cut them down by 1.5cm vertically to fit</del> | ||
| - | * Fix-up the head: [[http://www.groco.net/svc-main.htm|http://www.groco.net/svc-main.htm]] | ||
| * Add mixing bowl below water separator/fuel filter | * Add mixing bowl below water separator/fuel filter | ||
| | | ||
iw31/to-do.txt · Last modified: 2016/06/22 08:27 by ben
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
