..., etc.



==== Misc Info ====

  * Hatch dimensions: 89 x 66cm
  * Motor mount dimensions: 20 x 23cm, 3x1/2" ply
  * Toe rail: 5.2m
  * Tiller: 57cm + rise of 10cm
  * Barber haul cleat wood bases: 7 x 3.5cm

==== To-Do ====

=== Engine/Systems ===

  * Install security bolts
  * motor mount, sliding up, could be lowered a bit?

=== Mast ===

  * Need to bend windex indicators back into place
  * Need a bigger/stronger baton installed on the back stay

=== Sails/Rigging ===

  * **New sail cover** to allow leaving sail slides in the slot

=== Hull ===

  * <del>Sand and</del> varnish tiller, could use two more coats 
  * Replace toe-rails or patch broken toe-rail section (have 1m teak piece)
  * Replace or refinish hatch-cover
  * Install external hatch handle
  * Replace wood underneath spinnaker barber-haul cleats
  * Patch random small cracks on deck & in cockpit

=== Cabin ===

  * Remove old speed log and fill holes
  * File pantry and stove cover doors down to allow for expansion
  * Re-attach trim to various panels
  * Floor board reinforce forward port side
  * Floor board sand down bilge cover 
  * Paint inside walls near cabin entrance
  * Sand and varnish walls underneath added deck supports (varnish is peeling)

=== Long-term ===

  * Safety lines - or at least a bow pulpit
  * Lazy jacks?
  * Window replacement
  * Find replacement mast support pole? Need to prime the top section of the pole, a bit of rust. 
  * Replace motor mount plywood

==== Completed ====


=== Hull ===

  * <del>Weld tiller bracket back together</del>
  * <del>Patch small paint crack just above water line on starboard side near stern</del>
  * <del>Check rudder bearings and shaft condition</del> Should be okay for a long time to come.
  * <del>Bottom paint</del>

=== Mast ===

  * <del>Remove lost/dropped halyard blocks from center of mast</del> DONE!
  * <del>Either get 12-20 screws for spreaders or drill out to MM size</del> Drilled and tapped to M6!
  * <del>New Windex</del>
  * <del>Replace masthead lamp with LED</del>
  * <del>Install baton to lift backstay over sail headboard when tacking?</del>
  * <del>Forestay- rubs against jib halyard sheave, move it outside of the sheave position or remember to keep backstay loose (Found a suitable piece of steel to use to move the stay forward a centimeter or two)</del>Sheave was in great shape, this isn't necessary
  * <del>Replace lower boom kicker bracket (maybe upper too?) with something more sturdy</del>Bent back into shape, re-riveted

=== Sails/Rigging ===

  * <del>Shorten lower boom kicker length and re-attach (will allow more downward movement), need hacksaw and riveter at the boat</del>
  * <del>Re-install washers on jib halyard block</del>

=== Cabin === 

  * <del>Glue metal plate back into place under stove hatch - don't think it will last, need screws instead (DIDN'T hold).</del>Bolted down.

==== Bottom painting supplies ====

  * <del>masks</del>
  * <del>gloves</del>
  * <del>scrapers</del>
  * <del>masking tape</del>
  * <del>drop cloths</del>
  * <del>containers to mix epoxy paint (that won't melt, tin cans maybe)</del>
  * <del>sand paper</del>
  * <del>sanding blocks</del>
  * <del>beer</del>
  * <del>bourbon</del>
..., etc.

User Tools

Site Tools

Page Tools
